书名页

安徽省市场监督管理局公告

前　　言

1　总　则

2　术语和符号

• 2.1　术　语

• 2.2　符　号

3　基本规定

• 3.1　一般规定

• 3.2　工作程序及基本要求

• 3.3　抽样方法

• 3.4　检测报告

4　墙体保温系统节能检测

• 4.1　一般规定

• 4.2　基层墙体与胶粘剂/界面砂浆的拉伸粘结强度

• 4.3　保温层厚度和干密度

• 4.4　保温板材粘贴面积比

• 4.5　保温系统拉伸粘结强度

• 4.6　饰面砖粘结强度

• 4.7　锚栓抗拉承载力标准值

• 4.8　保温系统抗冲击性能

• 4.9　外墙节能构造

• 4.10　抹灰砂浆拉伸粘结强度

5　围护结构节能检测

• 5.1　一般规定

• 5.2　围护结构传热系数

• 5.3　围护结构热工缺陷

6　幕墙、外门窗节能检测

• 6.1　一般规定

• 6.2　外窗外遮阳设施

• 6.3　外窗气密性

• 6.4　中空玻璃密封性能

• 6.5　化学锚栓承载力

7　供暖、空调和通风系统节能检测

• 7.1　一般规定

• 7.2　室内温湿度

• 7.3　供暖系统室外管网热损失率

• 7.4　供暖系统室外管网水力平衡度

• 7.5　通风空调系统的风量

• 7.6　各风口的风量

• 7.7　风道系统单位风量耗功率

• 7.8　空调机组的水流量

• 7.9　空调系统冷水、热水、冷却水的循环流量

8　配电与照明系统节能检测

• 8.1　一般规定

• 8.2　平均照度与照明功率密度

• 8.3　功率因数

• 8.4　电压偏差

• 8.5　谐波电压及谐波电流

9　太阳能光热系统检测

• 9.1　一般规定

• 9.2　集热系统效率

• 9.3　贮热水箱热损因数

10　太阳能光伏系统检测

• 10.1　一般规定

• 10.2　光电转换效率

11　地源热泵系统检测

• 11.1　一般规定

• 11.2　制热性能系数和制冷能效比

附录A　检测设备性能要求

附录B　建筑节能工程现场检测工作流程图

附录C　围护结构热工缺陷检测流程图

本规程用词说明

引用标准名录

1　General Provisions

2　Terms and Symbols

• 2.1　Terms

• 2.2　Symbols

3　Basic Provisions

• 3.1　General Requirements

• 3.2　Working Procedures and Basic Requirements

• 3.3　Sampling Methods

• 3.4　Test Report

4　Energy Efficiency Inspection of Wall Insulation System

• 4.1　General Requirements

• 4.2　Tensile Bond Strength between the basal layer of Walls and Adhesive/Interface Mortar

• 4.3　Insulation Layer Thickness and Dry Density

• 4.4　Paste Area Ratio of Insulation Board

• 4.5　Tensile Bond Strength of Insulation System

• 4.6　Bonding Strength of Decorative Tiles

• 4.7　Standard Value of Tensile Bearing Capacity of Anchor Bolts

• 4.8　Impact Resistance of Insulation System

• 4.9　Energy—saving Construction of Exterior Wall

• 4.10　Tensile Bond Strength of Plastering Mortar

5　Energy Efficiency Inspection of Building Enclosure

• 5.1　General Requirements

• 5.2　Heat Transfer Coefficient of Building Enclosure

• 5.3　Thermodynamic Disfigurements of Building Enclosure

6　Energy Efficiency Inspection of Curtain Wall,External Doors and Windows

• 6.1　General Requirements

• 6.2　Shading Devices for External Windows

• 6.3　Air Tightness of External Windows

• 6.4　Sealing Performance of Insulating Glass

• 6.5　Bearing Capacity of Chemical Anchor Bolts

7　Energy Efficiency Inspection of Heating，Air Conditioning and Ventilation Systems

• 7.1　General Requirements

• 7.2　Indoor Temperature and Humidity

• 7.3　Heat Loss Rate of Outdoor Pipe Network of Heating System

• 7.4　Hydraulic Balance of Outdoor Pipe Network of Heating System

• 7.5　Air Volume of Ventilation and Air Conditioning System

• 7.6　Air Volume of Each Outlet

• 7.7　Power Consumption per Unit Air Volume of Air Duct System

• 7.8　Water Flow Rate of Air Conditioning Unit

• 7.9　Circulation Flow of Cold Water，Hot Water and Cooling Water in Air Conditioning System

8　Energy Efficiency Inspection of Power Distribution and Lighting System

• 8.1　General Requirements

• 8.2　Average Illumination and Lighting Power Density

• 8.3　Power Factor

• 8.4　Voltage Deviation

• 8.5　Harmonic Voltage and Harmonic Current

9　Inspection of Solar Photothermal System

• 9.1　General Requirements

• 9.2　Efficiency of Heat Collection System

• 9.3　Heat Loss Factor of Heat Storage Tank

10　Inspection of Solar Photovoltaic System

• 10.1　General Requirements

• 10.2　Photoelectric Conversion Efficiency

11　Inspection of Ground-source Heat Pump System

• 11.1　General Requirements

• 11.2　Heating Performance Coefficient and Refrigeration Energy Efficiency Ratio

Appendix A　Performance Requirements for Testing Equipment

Appendix B　Work Flow Chart for Field Inspection of Building Energy Saving Projects

Appendix C　Flow Chart for Inspection of Thermodynamic Disfigurements of Building Enclosure

Explanation of Wording in This Standard

List of Quoted Standards