中华人民共和国住房和城乡建设部公告

前　言

1　总　　则

2　术　　语

3　供电与配电

• 3.1　负荷分级与供电电源

• 3.2　高压供配电系统

• 3.3　无功补偿

• 3.4　电能质量要求

• 3.5　变电所与配电所

• 3.6　继电保护与自动装置

• 3.7　电测量仪表装置

• 3.8　防火与蓄油设施

• 3.9　对相关专业的要求

4　余热电站

• 4.1　一般规定

• 4.2　电气部分

• 4.3　对相关专业的要求

5　厂区线路

• 5.1　一般规定

• 5.2　电缆线路

• 5.3　架空线路

6　电解整流所

• 6.1　一般规定

• 6.2　供电电源与接线系统

• 6.3　整流机组的选择及谐波治理

• 6.4　控制、保护与测量

• 6.5　母线、设备配置及接地

• 6.6　交流所用电系统

• 6.7　直流所用电系统

• 6.8　对相关专业的要求

7　车间电力设计基本规定

• 7.1　配电系统

• 7.2　配电设备

• 7.3　控制与保护

• 7.4　配电线路

• 7.5　电测量仪表

• 7.6　电气照明

• 7.7　建（构）筑物防雷

• 7.8　配电室与控制室

8　重有色金属冶炼厂车间电力设计

• 8.1　一般规定

• 8.2　原料车间

• 8.3　焙烧与烧结车间

• 8.4　熔炼车间

• 8.5　浸出过滤与净液车间

• 8.6　电解车间

• 8.7　对相关专业的要求

9　氧化铝厂车间电力设计

• 9.1　一般规定

• 9.2　原料车间

• 9.3　烧结与焙烧车间

• 9.4　高压溶出与熟料溶出车间

• 9.5　分解过滤与蒸发车间

10　铝电解车间电力设计

• 10.1　电解车间

• 10.2　铝锭铸造车间

11　镁钛与工业硅厂车间电力设计

• 11.1　一般规定

• 11.2　氯化竖式炉、钛熔矿炉与纯硅炉

12　炭素厂车间电力设计

• 12.1　一般规定

• 12.2　电煅烧炉

• 12.3　石墨化炉

13　氟化盐厂车间电力设计

14　稀有金属冶炼厂车间电力设计

15　硬质合金厂车间电力设计

16　半导体材料厂车间电力设计

17　公用设施电力设计

• 17.1　空气压缩机站

• 17.2　水　泵　站

• 17.3　发生炉煤气站

• 17.4　氢　气　站

• 17.5　氧　气　站

• 17.6　实验室和化验室

• 17.7　充　电　站

• 17.8　静电滤清器电源装置

• 17.9　大中型风机

附录A　有色金属冶炼厂一级负荷用电设备表

附录B　有色金属冶炼厂三级负荷用电设备表

附录C　整流机组继电保护整定计算

附录D　整流机组短路阻抗计算

附录E　三氯氢硅合成炉工频感应线圈计算

附录F　有色金属冶炼厂环境特征

附录G　有色金属冶炼厂一般照明照度标准

本规范用词说明

引用标准名录

1　General provisions

2　Terms

3　Power supply and distribution

• 3.1　Load ranking and power supply

• 3.2　High-voltage power supply and distribution system

• 3.3　Reactive compensation

• 3.4　Power quality requirements

• 3.5　Substation and distribution

• 3.6　Relaying and automechanism

• 3.7　Electrical measuring instrument device

• 3.8　Fire-proof and oil-reserving facility

• 3.9　Requirements for of the relevant discipline

4　Waste heat power station

• 4.1　General regulations

• 4.2　Electric part

• 4.3　Requirements for relevant discipline

5　Plant site circuit

• 5.1　General requirement

• 5.2　Cable line

• 5.3　Overhead line

6　Electrolytic rectifier system

• 6.1　General requirement

• 6.2　Power supply and wiring system

• 6.3　The selection of rectifier unit and harmonic control

• 6.4　Control,protection and measuring

• 6.5　Bus bar,equipment configuration and grouding

• 6.6　AC shop power system

• 6.7　DC shop power system

• 6.8　Requirements for relevant discipline

7　Basic regulations of workshop electric engineering

• 7.1　Power distribution system

• 7.2　Power distribution equipment

• 7.3　Control and protection

• 7.4　Power distribution line

• 7.5　Electrical measuring instrument

• 7.6　Electric lighting

• 7.7　Lightning protection of buildings and structures

• 7.8　Distribution room and control room

8　Workshop electric engineering of heavy nonferrous smelters

• 8.1　General requirement

• 8.2　Material workshop

• 8.3　Sintering and roasting workshop

• 8.4　Smelting workshop

• 8.5　Leaching, filtration and leach solution workshop

• 8.6　Electrolysis workshop

• 8.7　Requirements for relevant discipline

9　Workshop electric engineering of alumina plant

• 9.1　General requirement

• 9.2　Material workshop

• 9.3　Sintering and roasting workshop

• 9.4　Pressure digestion and agglomerate digestion workshop

• 9.5　Decomposition,filtration and evaporation workshop

10　Electric engineering of aluminum electrolysis workshop

• 10.1　Electrolysis workshop

• 10.2　Aluminum ingot casting workshop

11　Workshop electric engineering of Mg,Ti and Si plant

• 11.1　General requirement

• 11.2　Chloride vertical furnace,Ti smelting furnace and pure Si furnace

12　Electric engineering of carbon workshop

• 12.1　General requirement

• 12.2　Electric calciner

• 12.3　Graphitizing furnace

13　Workshop electric engineering of fluoride salt plant

14　Workshop electric engineering of rare metal smelter

15　Workshop electric engineering of cemented carbide plant

16　Workshop electric engineering of semi-conductor material plant

17　Electric engineering of utilities

• 17.1　Air compressor station

• 17.2　Pump station

• 17.3　Furnace gas station

• 17.4　Hydrogen station

• 17.5　Oxygen station

• 17.6　Laboratory

• 17.7　Charging station

• 17.8　Static filter power supply device

• 17.9　　Large and medium-sized fan

Appendix A　List of electrical equipment with class I load for nonferrous smelter

Appendix B　List of electrical equipment with class Ⅲ load for nonferrous metal smelter

Appendix C　Setting caculation of rectifier unit relay

Appendix D　Short-current impedance caculation of rectifier unit

Appendix E　Line-frequency induction coils caculation of trichlorosilane synthesis furnace

Appendix F　Enviromental characteristics of nonferroussmelters

Appendix G　Specification of general lighting illuminancefor nonferrous smelters

Explanation of wording in this code

List of quoted standards