4　设备基础、地脚螺栓和垫板

• 4.1　一般规定

• 4.2　设备基础

• 4.3　地脚螺栓

• 4.4　垫　　板

5　设备和材料进场验收

• 5.1　一般规定

• 5.2　设备及构件

• 5.3　材　　料

6　蒸汽轮机

• 6.1　一般规定

• 6.2　台　　板

• 6.3　轴承座、轴承、下汽缸和转子

• 6.4　通流部件

• 6.5　合　　缸

• 6.6　盘车装置

• 6.7　凝　汽　器

• 6.8　联　轴　器

7　燃气轮机

• 7.1　一般规定

• 7.2　整体型燃气轮机

• 7.3　支撑装置、下气缸

• 7.4　通流部件

• 7.5　燃　烧　室

8　煤气余压透平膨胀机

• 8.1　一般规定

• 8.2　下机壳、下叶片承缸和调节缸

9　煤气压缩机和增速机

• 9.1　一般规定

• 9.2　整体型煤气压缩机

• 9.3　轴流式煤气压缩机

• 9.4　离心式煤气压缩机

• 9.5　增　速　机

10　发　电　机

• 10.1　一般规定

• 10.2　整体型发电机

• 10.3　定子和转子

• 10.4　轴承座及轴承

• 10.5　氢冷轴密封装置

• 10.6　励磁机及集电环

11　余热锅炉

• 11.1　一般规定

• 11.2　锅炉钢架

• 11.3　汽包和联箱

• 11.4　受热面模块

• 11.5　烟　风　道

• 11.6　水压试验

• 11.7　严密性试验

12　设备试运转

• 12.1　一般规定

• 12.2　蒸汽轮机

• 12.3　燃气轮机

• 12.4　煤气余压透平膨胀机

• 12.5　煤气压缩机

• 12.6　发　电　机

13　安全与环境保护

• 13.1　一般规定

• 13.2　安　　全

• 13.3　环境保护

附录E　设备无垫板安装及流动灌浆工艺

• E.1　设备无垫板安装

• E.2　流动灌浆工艺

4 Equipment foundation,anchor bolts and bearing plates

• 4.1 General requirements

• 4.2 Equipment foundation

• 4.3 Anchor bolts

• 4.4 Bearing plates

5 Acceptance of equipment and materials in site

• 5.1 General requirements

• 5.2 Equipment and components

• 5.3 Materials

6 Steam turbines

• 6.1 General requirements

• 6.2 Sole plates

• 6.3 Bearing pedestal,bearing,lower casing and rotor

• 6.4 Through-flow parts

• 6.5 Joined together tops and bottom cylinders

• 6.6 Turning gears

• 6.7 Condensers

• 6.8 Couplings

7 Gas turbines

• 7.1 General requirements

• 7.2 Integral type gas turbines

• 7.3 Support devices and lower casings

• 7.4 Through-flow components

• 7.5 Combustion chambers

8 Gas pressure recovery turbo expanders

• 8.1 General requirements

• 8.2 Lower covers,the lower blade bearing cylinders and adjusting cylinders

9 Gas compressors and gear cases

• 9.1 General requirements

• 9.2 Integral type gas compressors

• 9.3 Axial flow type gas compressors

• 9.4 Centrifugal type gas compressors

• 9.5 Gear cases

10 Generators

• 10.1 General requirements

• 10.2 Integral type generators

• 10.3 Rotors and stators of generators

• 10.4 Bearing seats and bearings

• 10.5 Hydrogen cold shaft seal devices

• 10.6 Exciters and collector rings

11 Waste-heat boilers

• 11.1 General requirements

• 11.2 Boiler steel frame structure

• 11.3 Steam drums and headers

• 11.4 Heating surface modules

• 11.5 Air and flue gas ducts

• 11.6 Hydraulic tests

• 11.7 Tightness tests

12 Equipment test run

• 12.1 General requirements

• 12.2 Steam turbines

• 12.3 Gas turbines

• 12.4 Gas pressure recovery turbo expanders

• 12.5 Gas compressors

• 12.6 Generators

13 Safety and environmental protection

• 13.1 General requirements

• 13.2 Safety

• 13.3 Environmental protection

Appendix E Equipment installed without bed piece and flowable grout process