中华人民共和国住房和城乡建设部公告

前　　言

1　总　　则

2　术语和符号

• 2.1　术　　语

• 2.2　符　　号

3　基本规定

• 3.1　一般规定

• 3.2　场地、地基和基础

• 3.3　试验和观测

4　地震作用和结构隔震验算

• 4.1　一般规定

• 4.2　设计反应谱和地震动输入

• 4.3　地震作用计算

• 4.4　构件截面设计

• 4.5　上部结构变形验算

• 4.6　隔震层设计

• 4.7　下部结构设计

5　隔震支座及隔震构造

• 5.1　一般规定

• 5.2　隔震支座检验

• 5.3　隔震支座与结构的连接

• 5.4　隔　离　缝

• 5.5　穿越隔震层的固定设施和管线

• 5.6　伸　缩　缝

• 5.7　检修及隔震标识

6　多层与高层建筑

• 6.1　一般规定

• 6.2　隔震层设计

• 6.3　结构设计

7　大跨屋盖建筑

• 7.1　一般规定

• 7.2　隔震层设计

• 7.3　大跨屋盖结构设计

• 7.4　支承结构设计

8　多层砌体建筑和底部框架-抗震墙砌体建筑

• 8.1　一般规定

• 8.2　隔震层设计

• 8.3　结构设计

9　核电厂建筑

• 9.1　一般规定

• 9.2　隔震设计

• 9.3　楼层反应谱

• 9.4　隔震支座的要求

• 9.5　橡胶隔震支座的检验规则

• 9.6　地震监测与报警

10　既有建筑和历史建筑的隔震加固设计

• 10.1　一般规定

• 10.2　既有建筑的隔震加固设计

• 10.3　历史建筑的隔震加固设计

11　村镇民居建筑

• 11.1　一般规定

• 11.2　房屋隔震设计要点

附录A　隔震建筑抗震性能设计

附录B　复振型影响系数计算公式

附录C　隔震支座连接设计

附录D　隔震支座力学分析模型和基本力学性能要求

附录E　既有建筑加固墙体和柱的托换方法

本标准用词说明

引用标准名录

1　General provisions

2　Terms and symbols

• 2.1　Terms

• 2.2　Symbols

3　Basic requirements

• 3.1　General requirements

• 3.2　Site，soils and foundation

• 3.3　Test and observation

4　Earthquake action and seismic isolation checking

• 4.1　General requirements

• 4.2　Design response spectrum and ground motion input

• 4.3　Earthquake action

• 4.4　Component section design

• 4.5　Checking for superstructure deformation

• 4.6　Design for isolation layer

• 4.7　Design for substructure of isolation layer

5　Seismic isolator and isolation details

• 5.1　General requirements

• 5.2　Checking for seismic isolator

• 5.3　Connection of seismic isolator and structure

• 5.4　Isolation seam

• 5.5　Fixtures and piping across the isolation layer

• 5.6　Expansion joint

• 5.7　Inspection and isolation identification

6　Multi-story and tall buildings

• 6.1　General requirements

• 6.2　Design for isolation layer

• 6.3　Structrual design

7　Large-span roof buildings

• 7.1　General requirements

• 7.2　Design for isolation layer

• 7.3　Structrual design for large-span roof buildings

• 7.4　Supporting sturcture design

8　Multi-story masonry buildings and multi-story masonry building with R.C.frames on ground floors

• 8.1　General requirements

• 8.2　Design for isolation layer

• 8.3　Structrual design

9　Nuclear power plant buildings

• 9.1　General requirements

• 9.2　Design for seismic isolation

• 9.3　Floor response spectrum

• 9.4　Requirements for seismic isolator

• 9.5　Testing rules for rubber isolation bearings

• 9.6　Earthquake monitoring and alarm

10　Seismic isolation design for retrofit of existing or historic buildings

• 10.1　General requirements

• 10.2　Seismic isolation design for retrofit of existing buildings

• 10.3　Seismic isolation design for retrofit of historic buildings

11　Rural residential buildings

• 11.1　General requirements

• 11.2　Building isolation design essentials

Appendix A　Seismic performance design of seismically isolated buildings

Appendix B　Formula for the influence coefficient of complex mode

Appendix C　Connection design of isolation bearing

Appendix D　Mechanical analysis model of isolation bearing and basic mechanical performance requirements

Appendix E　Support method for strengthening the existing building wall and column

Explanation of wording in this standard

List of quoted standards